Quick Clarifications In Regards To Builds
-
To make it work in that case you’d need an angle grinder as there’s only 7 expansion slots and you’s need 8 for those cards. :P
Additionally you’d need a serious water cooling setup. All told your looking at around ~1.1KW of heat going in that case so it’s like sticking a fan heater in a box. It ain’t gonna end well.
Practically every 4 card rig i’ve seen is open air. Whether that’s a crate or a custom build frame work like mine it’ll be easier/cheaper/better than an enclosed jobby.
Here’s 1 of mine…
-
[quote name=“Nutnut” post=“19355” timestamp=“1372795839”]
To make it work in that case you’d need an angle grinder as there’s only 7 expansion slots and you’s need 8 for those cards. :PAdditionally you’d need a serious water cooling setup. All told your looking at around ~1.1KW of heat going in that case so it’s like sticking a fan heater in a box. It ain’t gonna end well.
Practically every 4 card rig i’ve seen is open air. Whether that’s a crate or a custom build frame work like mine it’ll be easier/cheaper/better than an enclosed jobby.
Here’s 1 of mine…
[IMG]http://imageshack.us/a/img7/4227/p1000305fv.jpg[/img]
[/quote]Once I get up to 4 in one case ill post pics or a vid…been too busy with my move from ME to NH. I am using a Fractal Design XL…the key is that I have 2x 252 cfm Deltas and 2x 50w Rheostats sitting in my extra parts bin from my old ultimate air cooled rig. I don’t think ill run into any problems at all. Just need enough CFM and proper fan locations and it is totally viable.
-
With all the deltas in the world it doesn’t change the fact that you need 8 expansion slots in the case but you only have 7. ;)
Also the issue you’ll have is that all 4 cards will be bunched up (back of one card will be practically touching the front of the next) so cool air can’t get in. In fact the hot air gets sucked in instead and it compounds up. In the end the top card (cpu side) runs 20 to 30c hotter than the bottom. My open air rigs make use of multple 4000cfm air movers and still struggle to stay below 80c in the summer. Granted they are oc’d but nonetheless…
If you succeed without water cooling I’d patent the design. Believe me I’ve tried in a haf-x and failed. That case now has a single gtx580 in it. :'(
-
[quote name=“Nutnut” post=“19391” timestamp=“1372805225”]
With all the deltas in the world it doesn’t change the fact that you need 8 expansion slots in the case but you only have 7. ;)Also the issue you’ll have is that all 4 cards will be bunched up (back of one card will be practically touching the front of the next) so cool air can’t get in. In fact the hot air gets sucked in instead and it compounds up. In the end the top card (cpu side) runs 20 to 30c hotter than the bottom. My open air rigs make use of multple 4000cfm air movers and still struggle to stay below 80c in the summer. Granted they are oc’d but nonetheless…
If you succeed without water cooling I’d patent the design. Believe me I’ve tried in a haf-x and failed. That case now has a single gtx580 in it. :'(
[/quote]The Fractal I have has 9 expansion slots and i got it for like $80. You can cool anything with proper voltages and static pressure. This is also going to be used to replace my aging gaming rig which will be turned into a mining only one. Ill have pics in about 3 weeks after my move is finished and I have time to work on machines again. I am working on building a custom made fan bracket that will come from the bottom of the case up behind the butt of the cards and hold 2 120mm fans. The trick is eliminating heat pockets on your cards while they are close together.
-
[quote name=“Nutnut” post=“19355” timestamp=“1372795839”]
To make it work in that case you’d need an angle grinder as there’s only 7 expansion slots and you’s need 8 for those cards. :P[/quote]b-b-b-b-but MAGIC!
[quote]Additionally you’d need a serious water cooling setup. All told your looking at around ~1.1KW of heat going in that case so it’s like sticking a fan heater in a box. It ain’t gonna end well.[/quote]
Yup, dumped the case back into inventory. Bought closet shelving, couldn’t mount the way I would’ve liked, bought crates that wound up costing more than the shelving, running it in there now.
[quote author=RIPPEDDRAGON link=topic=2323.msg19557#msg19557 date=1372875223]
The Fractal I have has 9 expansion slots and i got it for like $80. You can cool anything with proper voltages and static pressure.
[/quote]His counter point may very well then be that I, myself, have no idea what static pressure is. -
UPDATE: We’re up on two cards! Right before I have to unplug for the day.
[img]http://i.imgur.com/kDa0oHI.jpg[/img][quote]Is that a drumstick[/quote]
That is indeed a drumstick. And I need it back now.longshot:
[img]http://i.imgur.com/zoTHwQD.jpg[/img]
When the powered risers get here, I’ll be ready to implement the rest.
[img]http://i.imgur.com/71UBUCl.png[/img]
Anything unusual? Is 70°C usual? -
Very nice!
If you manage to keep below 70c with 4 cards you’re doing v.well. Generally up to 85c is acceptable but below 80 is better. Sometimes you just can stop it rising. I have a couple of cards (maxed 7970s) that run at 80+ no matter what i do. I think i need to re-apply the thermal pads/paste. the rest are all 70(ish).
-
[quote]Or am I, and I am seriously not wanting to be tongue-in-cheek about this but it crossed my mind so I figured I should bring it up, risking having a fan so powerful that it slows the fans on the GPUs?[/quote]
Thankfully this wasn’t so much of an issue; though that vornado is pushing the GPU, CPU and power supply fans around when they’re not on.
Now my current issue is any time I start tweak settings, clock, memory, intensity, my hashrate dips 50k. At one point, and silly me forgot to notate where, but I raised it where I was pulling 612 but then started getting rejected blocks. Eventually one of the cards reported SICK and the whole thing just died.
So I’m back to stock settings, but I’m coveting the high ends of [url=http://litecoin.info/Mining_Hardware_Comparison]these results[/url]. I’ll keep tweaking I guess.
-
Uh, with this Seasonic that I got it has two CPU cables. One that fits perfectly and one that looks like it’s for Pentium based boards. Thing is on the back of the power supply, there’s two spots for CPU, and if I use the one that fits the board perfectly, it takes up a PCI-E power slot. The Pentium based one apparently has it’s own socket?
I’m assuming this matters, so how’d you guys get this combo to go? Will be reviewing your pictures for clues.
-
Dunno what board your running on but the CPU output on the PSU suits the cable that plugs directly in to my mobo.
No magic necessary.
Pics?
-
[quote name=“Nutnut” post=“21117” timestamp=“1373480241”]
Dunno what board your running on but the CPU output on the PSU suits the cable that plugs directly in to my mobo.No magic necessary.
Pics?
[/quote]The GIGABYTE GA-990FXA-UD3.1. Picture for the back of the power supply. I’ve been plugging in the top right hand corner and the cable goes right to and matches the notches (rounded and squared, you know) on the board. That worked for two cards. Adding more I’ll need all 4 of those PCI-E sockets back there, right?
2. This picture shows what I had plugged in there and where there’s empty holes with no pins. On the opposite side of the cable, as you’ll see in picture 3, it’s just 8 pins but the pattern is the exact same as the 8 pins that are occupied that you see in this pic. If I reverse the cable, plugging the eight that were in the board into the CPU only socket on the power supply as you saw on the bottom left of the power supply in the first picture, the extra, empty pins on the bit of the cable I’m showing here is blocked by a square on the board keeping it from being plugged in and the empty pins from overhanging.
3.Here’s the AMD cable that was working but takes up one of my PCI-E power sockets.
4. Here’s the intel cable that can plug into the lower left socket of the power supply, but has that split socket on the other side that won’t match up with the power connector on the board.
I’ve probably over explained it and am over thinking it maybe. I know there’s cables to connect SATA to the two six pins on the graphics card, but I was under the impression I needed all those available sockets under SATA for my powered risers.
I guess that’s my sticking point and why you didn’t have an issue - you don’t run powered risers do you?
EDIT: oh for f- there’s six sockets for sata there not 4. There’s probably plenty of room. Checking.
[attachment deleted by admin]
-
[quote name=“HopeStillFlies” post=“21126” timestamp=“1373482386”]
[quote author=Nutnut link=topic=2323.msg21117#msg21117 date=1373480241]
Dunno what board your running on but the CPU output on the PSU suits the cable that plugs directly in to my mobo.No magic necessary.
Pics?
[/quote]The GIGABYTE GA-990FXA-UD3.1. Picture for the back of the power supply. I’ve been plugging in the top right hand corner and the cable goes right to and matches the notches (rounded and squared, you know) on the board. That worked for two cards. Adding more I’ll need all 4 of those PCI-E sockets back there, right?
2. This picture shows what I had plugged in there and where there’s empty holes with no pins. On the opposite side of the cable, as you’ll see in picture 3, it’s just 8 pins but the pattern is the exact same as the 8 pins that are occupied that you see in this pic. If I reverse the cable, plugging the eight that were in the board into the CPU only socket on the power supply as you saw on the bottom left of the power supply in the first picture, the extra, empty pins on the bit of the cable I’m showing here is blocked by a square on the board keeping it from being plugged in and the empty pins from overhanging.
3.Here’s the AMD cable that was working but takes up one of my PCI-E power sockets.
4. Here’s the intel cable that can plug into the lower left socket of the power supply, but has that split socket on the other side that won’t match up with the power connector on the board.
I’ve probably over explained it and am over thinking it maybe. I know there’s cables to connect SATA to the two six pins on the graphics card, but I was under the impression I needed all those available sockets under SATA for my powered risers.
I guess that’s my sticking point and why you didn’t have an issue - you don’t run powered risers do you?
EDIT: oh for f- there’s six sockets for sata there not 4. There’s probably plenty of room. Checking.
[/quote]I think i need sleep coz i’m as confused as heck. :-[
I have the same mobo, and psu and I use the on in pic 4.
-
I was totally sweating because those pins don’t match exactly. Took it home to organize and went ahead and used that split wire and it worked fine. Thanks.
-
[quote name=“d2” post=“21215” timestamp=“1373526639”]
[quote author=HopeStillFlies link=topic=2323.msg21201#msg21201 date=1373514508]
I was totally sweating because those pins don’t match exactly. Took it home to organize and went ahead and used that split wire and it worked fine. Thanks.
[/quote]I have the exact same motherboard and PSU and it matched up fine but glad to hear you are running now!
[/quote]+1
-
Haha. Oh geez.
Okay, I’ve been offline for the past 2 working days because something happened where I was tweaking the cgminer config file (honest. swear to [i]god[/i] that’s all I touched.) and the next thing I know the board was rejecting the USB stick. I tried fixing it with no luck ended up giving up and just reinstalling and reconfiguring everything. THAT’S never going to happen again, losing so much time that could’ve been spent mining, so I’m going to make a disk image of the OS that I can replicate the next time I pull the machine down, which should be tonight.
Have you two noticed anything where when booting up the machine says to plug in something bootable, even though one reboot ago the stick was working fine? All I changed was stuff in my cgminer startup script, copying the settings in rgfii’s build.
-
Can’t say that I have but then I never had much luck with booting from USB so prefer to stick with the standard hdd (SSD).
Sounds like you somehow corrupted the USB sticks boot sectors. Did you remove the USB key?
-
I have 20GB SATAs from old Xbox encasings laying around all over the place. Next time this thing goes down I’ll have one of those prepped. I just figured I’d turn off power to everything but USB (no sata, no USB3.0, no 1394, etc.) but it really makes no difference in the grand scheme of things.
And yesterday after rebooting my machine it would get right to work but this morning it booted and went into GRUB so apparently it’s not been doing crap for the entirety of the day. Ugh. Going to go find a way to knock that crap off now.*
Nevermind, it’s going right to desktop again now.
-
Okay, everything is going great. So great I’m scared to screw with it, BUT:
1. I’m seeing results in the hardware comparison ranging between 600-700, but I’m topping out at 570 per card by:
Intensity = 20
Engine = 1050
Memory =1400
Powertune = 20
And the little button pressed on the top (looked like some others had theirs pressed, even with those settings put in by hand it didn’t kick to 570 unless the button was pushed - or does it do absolutely nothing?)
I see other metrics like shading, thread concurrency, etc. but I really want to know what that stuff [i]means[/i] before I start randomly plugging in there. What’s the baseline config file for cgminer linux that I can tweak instead of starting with a blank page? Is there any chance someone can paste up one they’ve used for this similar hardware? It’d be nice to have a normal config file anyway; I’m putting all this stuff in by hand each time I boot up in the morning.2. …can I run 6 7950s off this board and power supply? It’s physically possible, but [i]should I[/i]?
-
[quote name=“HopeStillFlies” post=“22536” timestamp=“1374434735”]
Okay, everything is going great. So great I’m scared to screw with it, BUT:1. I’m seeing results in the hardware comparison ranging between 600-700, but I’m topping out at 570 per card by:
Intensity = 20
Engine = 1050
Memory =1400
Powertune = 20
And the little button pressed on the top (looked like some others had theirs pressed, even with those settings put in by hand it didn’t kick to 570 unless the button was pushed - or does it do absolutely nothing?)
I see other metrics like shading, thread concurrency, etc. but I really want to know what that stuff [i]means[/i] before I start randomly plugging in there. What’s the baseline config file for cgminer linux that I can tweak instead of starting with a blank page? Is there any chance someone can paste up one they’ve used for this similar hardware? It’d be nice to have a normal config file anyway; I’m putting all this stuff in by hand each time I boot up in the morning.2. …can I run 6 7950s off this board and power supply? It’s physically possible, but [i]should I[/i]?
[/quote]I’ll address the second point first… Even that monster supply will not run 6 7950’s. Especially when OC’d.
As for point 1, i’m writing up a tuning guide but it a looong way from ready. The little button you speak of has me confused, do you mean the bios switch that switches between BIOS 1 and Bios 2? If so it will do nothing unless you have flashed a new firmware to your card.
Shaders are the number of shaders your card has. For your 7950 its 1792. That’s a fixed number and if left blank CG should autodetect. As for the rest of the settings, have a look here… [url=https://github.com/ckolivas/cgminer/blob/master/SCRYPT-README]https://github.com/ckolivas/cgminer/blob/master/SCRYPT-README[/url]. I think it explains everything nicely but i’m writing a new guide to elaborate and simplify it a bit.
-
[quote name=“HopeStillFlies” post=“22536” timestamp=“1374434735”]
Okay, everything is going great. So great I’m scared to screw with it, BUT:1. I’m seeing results in the hardware comparison ranging between 600-700, but I’m topping out at 570 per card by:
Intensity = 20
Engine = 1050
Memory =1400
Powertune = 20
And the little button pressed on the top (looked like some others had theirs pressed, even with those settings put in by hand it didn’t kick to 570 unless the button was pushed - or does it do absolutely nothing?)
I see other metrics like shading, thread concurrency, etc. but I really want to know what that stuff [i]means[/i] before I start randomly plugging in there. What’s the baseline config file for cgminer linux that I can tweak instead of starting with a blank page? Is there any chance someone can paste up one they’ve used for this similar hardware? It’d be nice to have a normal config file anyway; I’m putting all this stuff in by hand each time I boot up in the morning.2. …can I run 6 7950s off this board and power supply? It’s physically possible, but [i]should I[/i]?
[/quote]6x 7950 forget it, that psu is absolutely perfect for running 4x7950 clocked (then you use around 1400w at socket, which is 1120 at dc side).
have the same setup running dead stable with 650khash each.(thanks to nutnut config), at 77degrees in an room with around 30degrees. (high power fans for airflow around cards)Heres my settings:
cgminer --scrypt -w 256 --shaders 0 --intensity 20 -v 1 -g 1 --lookup-gap 2 --thread-concurrency 21712 --gpu-engine 1100 --gpu-memclock 1500 --gpu-memdiff 0 --gpu-powertune 20 --gpu-fan 85 --temp-target 80 --temp-cutoff 90 -o ftc.nut2pool.com:5555 -u x -p x --failover-only -o 192.168.0.2 -u x -p x --api-listen --api-port xxxx --api-allow x.x.x.xDo you use powered risers? with four cards you REALLY should… i have 4 burned mobos to prove it ;)